CR-BS-7003 is made by hybrid braiding of polyester monofilaments and multifilaments. This product can effectively reduce noise generated by wire harness vibration and it’s good wear resistance helps prolong the service life of wire harnesses. Meanwhile, it’s lightweight design can reduce the burden on the vehicle body.
Download Product Manual:
the CR-BS-7003 sleeve is a hybrid-braided polyester sleeve for wire harnesses exposed to vibration, rubbing, and constrained installation paths. Its longitudinal self-closing construction lets an installer place the wrap around an assembled harness rather than thread the harness through a closed tube. This makes the product a practical option where access after assembly, inspection, or rerouting matters.
The product combines polyester monofilaments and multifilaments in a flexible braid. The stated purpose is to reduce noise associated with wire-harness vibration while adding an abrasion barrier. It is not a substitute for validating the full harness design: routing, clips, bend radius, temperature, and bundle diameter still determine the result in service.
this braided wrap is specified for continuous use from -40°C to 150°C. The product description also states heat ageing at 175°C for 240 hours with no recorded damage. These figures are useful selection inputs, but the actual peak temperature and exposure duration at the routing location should be confirmed before release.
| Part No. | Nominal I.D. (mm) | Applicable Range (mm) | Reel Length (m/reel) |
|---|---|---|---|
| CR-BS-70031001 | 10 | 10–11 | 100 |
| CR-BS-70031301 | 13 | 12–14 | 100 |
| CR-BS-70031601 | 16 | 15–17 | 100 |
| CR-BS-70031901 | 19 | 18–22 | 50 |
| CR-BS-70032501 | 25 | 23–28 | 50 |
| CR-BS-70033201 | 32 | 29–35 | 25 |
Six nominal sizes cover bundle diameters from 10 mm to 35 mm. Cut-to-length service and non-standard sizes are described as available on request. Measure the assembled bundle, including any branch-outs or retention points, then compare that measurement with the applicable range rather than selecting only by nominal diameter.
the selected sleeve can be opened along its length, positioned over a completed harness, and released without wrapping tape for closure. This format can simplify retrofit, maintenance, and inspection work where disconnecting the harness is undesirable. In a repair station or a late-stage assembly operation, the difference between a wrap format and a closed sleeve can be operationally significant.
The hybrid braid is intended to absorb vibration energy and help limit harness-to-panel or harness-to-bracket noise. For NVH-sensitive routing, assess the contact points and the securing method together with Sound Absorption Self-closing Wrap-CR-BS-7003. Noise performance depends on the installed system, not on a sleeve alone.
The braided construction provides a protective layer where a harness can contact brackets, clips, or adjacent structure. This is relevant in engine compartments, chassis-adjacent zones, and moving equipment. Confirm that the route avoids sharp edges and that fixing points do not create concentrated wear.
Sound Absorption Self-closing Wrap-CR-BS-7003 is described as lightweight, which can be useful where harness mass and package space are reviewed as part of a vehicle or equipment design. The product provides protection without the rigid profile of a conduit.
Start with the bundle diameter. A larger sleeve is not automatically better: an oversized wrap can move relative to the harness and create friction. Select the applicable range that gives a conforming fit while allowing installation. Next, verify the actual thermal envelope. For low-temperature installation, assess cold-bend performance under the project’s real minimum temperature; do not infer arctic suitability from a general rating alone.
Then decide whether a self-closing design matches the work sequence. Sound Absorption Self-closing Wrap-CR-BS-7003 is especially relevant when the harness is already assembled or where future access is expected. For a permanently enclosed route, compare installation requirements and retention needs before choosing a wrap format.
Finally, clarify the material requirement. The allocated term silicone rubber cable sleeve should not be treated as a material claim for this product: CR-BS-7003 is described as a polyester hybrid braid. If a project specifically requires silicone rubber, obtain a separate material confirmation. The allocated term braided wire sleeving is applicable as a broad category, while the exact construction and operating conditions should govern final selection.
Sound Absorption Self-closing Wrap-CR-BS-7003 can be considered for engine-compartment and other NVH-sensitive harness routes where thermal exposure, vibration, and abrasion occur together. It may suit automotive programs that need an accessible protective layer; any vehicle-specific qualification remains the responsibility of the project team.
For new energy vehicle routing, the lightweight wrap format can support package-conscious harness protection. Evaluate electrical requirements separately, especially for high-voltage circuits, because this product description establishes mechanical and acoustic attributes rather than a complete electrical insulation specification.
In automation equipment, Sound Absorption Self-closing Wrap-CR-BS-7003 can help organize and protect harnesses subject to recurring motion and vibration. It may be useful where technicians need to inspect or rework a route without removing a closed protection tube.
The manufacturing site is described as certified to ISO 9001, IATF 16949, ISO 14001, ISO 45001, and GJB9001C. Product test reports are available on request. Certification information can support supplier evaluation, but it does not replace verification against the specific customer standard, market requirement, or installation condition.
For a quotation or technical review, provide the assembled bundle diameter, routing temperature, required reel length, installation method, and any required documentation. This information allows the technical team to confirm whether Sound Absorption Self-closing Wrap-CR-BS-7003 and the selected size fit the intended application.
Before production release, inspect the harness route with the sleeve fitted. Check closure around straight sections, bends, branches, and clips. Verify the selected applicable range at the largest assembled section, and confirm that brackets or direction changes do not create a sharp contact point during vibration.
For temperature-critical locations, record the expected continuous temperature, potential short-duration peaks, and the effect of nearby heat sources. For noise-sensitive locations, evaluate the complete assembly because clamp force, clearance, and harness movement affect audible results. A sample installation can also confirm handling, access, and serviceability before a full production order. If documentation is required for an approval process, request the relevant product test reports and align them with the customer’s own acceptance criteria.
CR-BS-7003 is made by hybrid braiding of polyester monofilaments and multifilaments. This product can effectively reduce noise generated by wire harness vibration and it’s good wear resistance helps prolong the service life of wire harnesses. Meanwhile, it’s lightweight design can reduce the burden on the vehicle body.
Download Product Manual: