Self-Closing Orange Adhesive Textile Wrap — FMVSS 302 Flame Retardant, ISO 6722-1 Class 4 Abrasion Resistant, -40°C to 150°C for EV High-Voltage Harness Protection
Download Product Manual:
Orange Adhesive Textile Self-closing Wrap-CR-BS-4006 is an orange, adhesive-backed polyester textile wrap for organizing and protecting wire bundles. Its self-closing construction lets an installer position the material around an assembled harness without a separate tape wrap. Orange may support route identification, but it does not establish electrical suitability; confirm system requirements, interfaces, documentation, and application validation before approval.
The supplied description states a 0.6 ± 0.15 mm wall thickness and a stated operating range from -40°C to 150°C. It also states that the material passed a low-temperature bending test at -40°C for four hours without cracking, a thermal-aging impact test at 175°C for 336 hours without cracking or fracture, and a hot-bend test at 175°C with a 180° bend and 1 kg load for three hours without damage or distortion. These statements provide a starting point for a technical review, not a substitute for the project-specific test plan.
The same source describes ISO 6722-1 Class 4 abrasion resistance at ≥5000 cycles, FMVSS 302 self-extinguishing behavior, and fluid and chemical resistance identified as D47 1924 with no fading or decomposition. Where a customer specification requires these characteristics, request the relevant current test report, sample identification, test conditions, and acceptance criteria. A standard reference can be relevant, but a reference alone does not establish that every end-use condition has been qualified.
| Listed property | Stated information |
|---|---|
| Construction | Adhesive-coated polyester textile |
| Wall thickness | 0.6 ± 0.15 mm |
| Stated operating range | -40°C to 150°C |
| Abrasion statement | ISO 6722-1 Class 4, ≥5000 cycles |
| Flammability statement | FMVSS 302 self-extinguishing |
Orange Adhesive Textile Self-closing Wrap-CR-BS-4006 is designed for a harness that may be difficult to sleeve from an end. Its edges close around the bundle, so the installer can cover a routed section without disconnecting terminals or reworking the entire assembly. This can be useful at branch points, around serviceable sections, or in constrained routing zones. The adhesive-backed closure is intended to hold the textile edges together; verify surface cleanliness, bundle geometry, bend movement, and the required overlap during process development.
It is tempting to assume that a larger sleeve or a thicker-looking wrap automatically gives better protection. That is not a reliable selection rule. The more useful question is whether the selected diameter, closure condition, movement range, and contact points match the actual harness installation. Excess clearance may allow movement at a fixed point, while too little clearance can complicate assembly or stress the closure.
The listed standard nominal inner diameters are 10, 13, 16, 19, 25, and 29 mm. The source lists 100 m reels for the 10, 13, and 16 mm sizes; 50 m reels for 19 and 25 mm; and 25 m reels for 29 mm. Confirm actual delivered dimensions, tolerances, cut lengths, reel configuration, and order details with the supplier before release. If a program uses a non-standard branch diameter or requires a special cut length, treat availability as a supplier confirmation rather than an assumed product feature.
| Part number | Nominal I.D. (mm) | Listed reel length (m) |
|---|---|---|
| CR-BS-40061014 | 10 | 100 |
| CR-BS-40061314 | 13 | 100 |
| CR-BS-40061614 | 16 | 100 |
| CR-BS-40061914 | 19 | 50 |
| CR-BS-40062514 | 25 | 50 |
| CR-BS-40062914 | 29 | 25 |
For a battery-pack or high-voltage harness, Orange Adhesive Textile Self-closing Wrap-CR-BS-4006 can be considered where visible orange routing and a textile wrap-around format are useful. The product’s stated temperature, abrasion, and flame-related information may be relevant to the review. However, high-voltage use requires broader engineering confirmation: protective wrapping does not by itself establish electrical insulation performance, voltage rating, or compliance with an OEM specification.
Harness routes near power electronics can combine temperature exposure, vibration, and limited installation space. The stated -40°C to 150°C range and hot-bend test can inform an initial screening discussion. Confirm local surface temperatures, exposure duration, fluid contact, edge contact, and routing restraints on the actual assembly. If the project involves recurring movement, evaluate the closure and textile against representative motion rather than relying only on static dimensions.
For serviceable sections, a self-closing format can simplify replacement or inspection. Define coverage length, termination clearance, and inspection points in the work instruction. Whether it is called a split wire wrap, snakeskin cable wrap, or heat resistant sleeve for wires, verify documented properties and intended application.
Start with the bundle diameter and route, then determine the required closure coverage and installation allowance. Next, compare the applicable temperature, abrasion, flammability, chemical-exposure, and color-control requirements with supplier documentation. Finally, validate a representative sample in the target assembly. This sequence helps prevent a common issue: selecting a wrap because it looks appropriate on a specification sheet before confirming the actual routing condition.
Orange Adhesive Textile Self-closing Wrap-CR-BS-4006 combines an adhesive self-closing textile format with orange identification and the stated performance information described above. It is best evaluated as one part of a complete harness-protection design. When a project requires formal compliance, documented test evidence and the final application conditions should guide the decision.
Self-Closing Orange Adhesive Textile Wrap — FMVSS 302 Flame Retardant, ISO 6722-1 Class 4 Abrasion Resistant, -40°C to 150°C for EV High-Voltage Harness Protection
Download Product Manual: