Welcome to our store!

nomex-braided-sleeving-cr-bs-3001, nomex-braided-sleeving-cr-bs-3001, /nomex-braided-sleeving
nomex-braided-sleeving-cr-bs-3001, nomex-braided-sleeving-cr-bs-3001, /nomex-braided-sleeving
Inquiry
nomex-braided-sleeving-cr-bs-3001, nomex-braided-sleeving-cr-bs-3001, /nomex-braided-sleeving
nomex-braided-sleeving-cr-bs-3001, nomex-braided-sleeving-cr-bs-3001, 
Inquiry

Nomex Braided Sleeving-CR-BS-3001

CR-BS-3001 is made of precision-woven Nomex fiber. It is self-extinguishing, flexible, and resistant to acid, oil, and alkali corrosion, ensuring that cable assemblies, hoses, and harnesses are protected from high temperatures, flames, cuts, and abrasion.

 

 

Nomex Braided Sleeving-CR-BS-3001Download Product Manual:

Nomex Braided Sleeving-CR-BS-3001Nomex Braided Sleeving-CR-BS-3001Nomex Braided Sleeving-CR-BS-3001

Request a Quote
  • Overview

Overview

Nomex Braided Sleeving-CR-BS-3001: braided protection for demanding routes

Nomex Braided Sleeving-CR-BS-3001 is a precision-woven protective sleeve for cable assemblies, hoses, and harnesses exposed to heat, abrasion, and common workshop or process fluids. The supplied product information identifies Nomex fiber construction, a flexible braided form, self-extinguishing behavior, and resistance to acid, oil, and alkali. It also lists a service range of -200°C to 350°C. These properties make the sleeve relevant where a basic ambient-temperature wrap is not enough.

Selection should begin with the actual route, not the product category alone. Measure the bundle, map sharp edges and movement points, identify nearby media, and define the expected temperature cycle. A sleeve is one element of an assembly; wire insulation, connectors, clamps, clearance, and installation quality also affect the final result. This practical boundary is especially important in high-temperature zones.

Confirm routing clearances, bundle movement, maintenance access, and required evidence with the responsible engineering team before final approval.

Assess the operating condition first

For Nomex Braided Sleeving-CR-BS-3001, confirm the highest and lowest expected temperature, whether the heat is continuous or intermittent, and whether the route is exposed to radiant heat, vibration, or direct contact. Record the bundle outer diameter after any tape or covering has been applied. A nominal width is a useful reference, but the applicable range is the more relevant fit criterion.

The product material describes self-extinguishing behavior after removal of an ignition source. That statement may be relevant to a flame-risk evaluation, but it is not a blanket approval for every finished harness. Where an end customer requires a defined method, report, or approval, request documentation that matches the actual assembly and target market. One document does not automatically cover every use case.

  • Thermal boundary: compare the supplied -200°C to 350°C range with the real duty cycle.
  • Mechanical boundary: inspect bends, clips, vibration points, and edges.
  • Fluid boundary: identify the actual fluid and likely exposure duration.
  • Validation boundary: define the evidence needed before production release.

Material and construction benefits

The braided construction of Nomex Braided Sleeving-CR-BS-3001 helps it follow non-linear cable and hose routes. The available product description positions the Nomex fiber material for environments where elevated temperature, flame-risk assessment, chemical contact, and abrasion may occur together. This combination can simplify the evaluation of a protective layer, while still leaving the engineering team responsible for confirming full-system compatibility.

Temperature performance. The stated -200°C to 350°C range provides a starting point for applications with broad thermal variation. It should not be used to assume that adjoining cable insulation, connectors, or mounting components have the same tolerance. Verify each component at the installation level.

Flame behavior. The supplied content describes inherent self-extinguishing behavior. If flame performance is critical, define the test configuration, acceptance requirement, and documentation scope in the inquiry. This is more useful than treating a broad material description as a universal compliance statement.

Chemical and abrasion considerations. The product is described as resistant to acid, oil, and alkali corrosion and suited to abrasion-prone routing. Good routing design remains necessary: a braided layer cannot correct a sharp edge, inadequate clearance, or poorly placed clamp.

Flexible coverage. The flexible form can be helpful around complex paths and constrained space. Choose the size using the actual bundle condition and confirm that the installed sleeve can accommodate bends without creating excess stress.

Listed sizes and fit guidance

The available table for Nomex Braided Sleeving-CR-BS-3001 includes five listed part numbers. Measure the largest practical bundle point, compare it with the applicable range, then review transitions and bends. A fit that appears acceptable on a straight sample can behave differently after routing through clamps or around a corner.

Part No. Reference width (mm) Applicable range (mm) Reel length (m) Art. No.
CR-BS-3001000308 3 ± 1 1–4 200 NX-003
CR-BS-3001001008 10 ± 2 7–11 100 NX-010
CR-BS-3001001308 13 ± 2 14–18 100 NX-013
CR-BS-3001001608 16 ± 2 15–20 100 NX-016
CR-BS-3001002008 20 ± 3 20–23 100 NX-020

The listed reel lengths are 100 m or 200 m, depending on the part number. If the project requires fixed cuts or a non-standard width, discuss the configuration before ordering and verify availability with the supplier.

Application review points

Aerospace and high-heat harness routes

Nomex Braided Sleeving-CR-BS-3001 can be assessed for routes where heat exposure, flexibility, and low added mass matter. Aerospace requirements are program-specific, so confirm applicable documentation, test conditions, and approval requirements with the responsible engineering team.

Vehicle and motorsport engine-bay routing

Engine-bay routes can combine heat, vibration, fluid exposure, and abrasion. The sleeve may be considered when a basic cable wrap is not suited to the documented condition. Installation details, clearance, and attachment method remain as important as the material selection.

Industrial process equipment

For industrial hot zones, document operating temperature, exposure duration, contamination, and maintenance practice before choosing a protective layer. If a site uses a specific safety or procurement standard, ask for product information that is relevant to that requirement instead of assuming generic category coverage.

Inquiry checklist

For Nomex Braided Sleeving-CR-BS-3001, include the bundle diameter, temperature profile, exposure type, requested reel or cut length, quantity, and documentation needs in the inquiry. Clear operating details allow a realistic size and material review. They also help distinguish a sleeve-layer requirement from wider assembly requirements.

Buyers comparing high temperature heat shrink tubing, solder sleeve heat shrink, cloth loom tape, or a 1 4 split loom tool should not treat those terms as direct equivalents. They refer to different functions, such as heat shrinking, soldered termination, wrapping, or routing access. This braided sleeve should be specified as a protective covering after the required function has been defined.

Before release, confirm the chosen part number, applicable range, requested documentation, and end-use validation. The supplied product information supports a focused engineering review; final suitability remains dependent on the documented installation condition.

Nomex Braided Sleeving-CR-BS-3001

CR-BS-3001 is made of precision-woven Nomex fiber. It is self-extinguishing, flexible, and resistant to acid, oil, and alkali corrosion, ensuring that cable assemblies, hoses, and harnesses are protected from high temperatures, flames, cuts, and abrasion.

 

 

Nomex Braided Sleeving-CR-BS-3001Download Product Manual:

Nomex Braided Sleeving-CR-BS-3001Nomex Braided Sleeving-CR-BS-3001Nomex Braided Sleeving-CR-BS-3001

Request a Quote

Featured Products

nomex braided sleeving cr bs 3001-2

Get a Free Quote

Our representative will contact you soon.
Email
WhatsApp
Mobile
Name
Company Name
Position
Message
0/1000