CR-BS-4010 is knitted from PET monofilament and multifilament. It has good abrasion resistance and noise reduction performance. The open structure makes it easy to install and remove.
Download Product Manual:
Knitted Self-closing Wrap-CR-BS-4010 is a knitted PET protective sleeve designed to wrap around wire harnesses where access after installation is useful. Its open construction closes around the bundle when released, so the sleeve can be installed without tape, clips, or special tools. It can also be opened again for inspection, maintenance, or rerouting without cutting the protective layer. This format is useful where connectors, branches, or installed components make a closed sleeve difficult to apply.
The product uses PET monofilament and multifilament in a knitted construction. The supplied product information describes a soft, flexible, lightweight outer layer with abrasion-resistance and noise-reduction performance. It is intended to protect and organize harnesses; it should not be treated as a sealed electrical enclosure or as evidence that a finished assembly meets requirements that have not been verified for that assembly.
| Characteristic | Specified information |
|---|---|
| Material | PET monofilament and multifilament, knitted construction |
| Operating temperature | -50°C to +150°C |
| Wall thickness | 1.0 ± 0.2 mm for listed standard sizes |
| Flammability | FMVSS 302; self-extinguishing after flame removal |
| Heat ageing reference | 175°C for 336 hours; no cracking or fracture reported |
| Standard nominal I.D. | 6, 8, 10, 13, 16, 19, 25, 29, 32, 38, and 45 mm |
The stated operating range and heat-ageing reference are selection inputs. They do not replace validation of the installed harness, its movement, neighboring materials, or any project-specific temperature and chemical exposure. If an application has unusual duty conditions, confirm the relevant test requirements before approving a size or material.
The self-closing configuration is the central advantage of Knitted Self-closing Wrap-CR-BS-4010. An installer places the harness through the opening, then lets the knitted construction close around the bundle. No locking clips, adhesive tape, or secondary fasteners are described as necessary for normal installation. For an existing route, the same opening permits access to an individual branch without removing a permanent tube or cutting the protection.
This can simplify work on bundles with branch-outs, connector ends, or later engineering changes. It may also support maintenance procedures where the harness must be inspected and then covered again. Actual installation time will depend on bundle geometry, the route, work access, and the assembly method; it should not be assumed from the sleeve format alone.
PET knitted construction gives the sleeve a flexible profile around the harness. The product information identifies a -50°C to +150°C operating range. For cold environments, evaluate the actual installation and bending condition rather than relying only on a nominal temperature value. For elevated-temperature zones, compare the real local temperature, duration, and surrounding components with the supplied product information.
The product is identified as meeting FMVSS 302 and as self-extinguishing after flame removal. When a customer specification refers to a flammability requirement, request the applicable supporting documentation and confirm whether the cited reference applies to the finished design. A materials statement does not automatically cover every system-level or regional requirement.
Knitted Self-closing Wrap-CR-BS-4010 is available in eleven listed nominal inner diameters. The 6 mm option is listed at 200 m per reel. The 8 mm, 10 mm, and 13 mm options are listed at 100 m per reel. The 16 mm, 19 mm, and 25 mm options are listed at 50 m per reel. The 29 mm, 32 mm, 38 mm, and 45 mm options are listed at 25 m per reel. The specified wall thickness is 1.0 ± 0.2 mm across these standard sizes.
| Nominal I.D. (mm) | Reel length (m/reel) |
|---|---|
| 6 | 200 |
| 8 / 10 / 13 | 100 |
| 16 / 19 / 25 | 50 |
| 29 / 32 / 38 / 45 | 25 |
Start selection with the installed outside dimension of the harness, including branches and any required movement. A bigger nominal diameter is not inherently more protective. Fit, coverage, clearance, routing hardware, and later service access all matter. The product information states that custom sizes and cut-to-length options are available upon request; confirm availability for a specific project and order quantity.
The supplied description presents this sleeve for automotive wire harness protection in engine compartments, cabins, door panels, and floor-routing channels. The self-closing format can be considered where harness access is important. Engineering teams should evaluate local heat, abrasion points, sharp edges, clips, vibration, and the finished assembly's validation plan.
In communication enclosures, a serviceable knitted sleeve can help organize cable bundles that may require inspection or additions. The open design supports access to the bundle, but it does not establish a sealing or ingress-protection rating. Review enclosure requirements independently.
The source material also identifies railway, rail-transit, and industrial uses. For these applications, review the route, contact surfaces, expected movement, temperature exposure, and customer documentation requirements before selection. The choice should reflect verified project requirements rather than a general assumption that one sleeve construction fits every condition.
Knitted Self-closing Wrap-CR-BS-4010 offers a PET knitted option for projects that value accessible harness coverage and tool-free installation. There is no universal best choice: the appropriate sleeve depends on the application, bundle geometry, temperature exposure, and validation requirements. For an enquiry, provide the required nominal diameter, operating environment, reel or cut-length requirement, and documentation needs so the proposed item can be matched to the intended harness design.
Confirm dimensions carefully.
CR-BS-4010 is knitted from PET monofilament and multifilament. It has good abrasion resistance and noise reduction performance. The open structure makes it easy to install and remove.
Download Product Manual: