DR diesel resistant heat-shrinkable tubing is made of special elastomer with a 2:1 shrinkage rate. Resistant to high temperature, flame retardant, oil and chemicals, flexible and especially resistant to diesel. Widely used for aviation, aerospace and military cables and wire harnesses, and automotive wire harnesses, with good resistance to diesel, aviation fuel, hydraulic fluid, lubricating oil and more.
Download Product Manual:
DR Diesel Resistant Heat-shrinkable Tubing is flexible 2:1 heat-shrinkable tubing made from special elastomer for wire and cable harness protection in demanding service environments. It is designed for applications where diesel, oils, chemicals, temperature exposure, and flame-retardant performance are important considerations. The product information describes especially strong resistance to diesel and identifies use in environments that may also involve aviation fuel, hydraulic fluid, and lubricating oil.
Selection should begin with the real operating boundary: harness size, service temperature, exposure medium, and shrinkage process. DR Diesel Resistant Heat-shrinkable Tubing has a stated operating temperature range of -75°C to 150°C and a minimum complete shrinkage temperature of 175°C. These values help buyers assess diesel-resistant material performance.
DR Diesel Resistant Heat-shrinkable Tubing combines flexibility with stated resistance to high temperature, flame, oil, and chemicals. The supplied data identifies conformance to MIL-DTL-23053/16. Review it with applicable program requirements because acceptance methods differ by application.
A heat-shrinkable sleeve must be assessed beyond its pre-shrink diameter. Material composition, heat application, bundle shape, and service medium all affect the finished result. This tubing has a stated 2:1 shrinkage rate and is intended to provide close-fitting protection when the specified process is used. Confirm bundle dimensions before heating and use a controlled method capable of reaching the stated complete shrinkage temperature.
The original product data provides measurable requirements and typical values, but does not replace finished-assembly validation. Where a project has a specific fluid, dwell time, temperature cycle, or approval requirement, assess the completed assembly under that condition.
| Performance item | Stated requirement | Typical value |
|---|---|---|
| Tensile strength | ≥8 MPa | ≥16 MPa |
| Breakage elongation | ≥250% | ≥500% |
| Complete shrinkage temperature | 175°C | 175°C |
| Axial shrinkage rate | ±10% | ±5% |
| Tensile strength after aging at 150°C for 168 h | ≥10.3 MPa | ≥14 MPa |
| Elongation after aging at 150°C for 168 h | ≥200% | ≥450% |
| Cold impact at -65°C for 4 h | No embrittlement or crack | No embrittlement or crack |
| Thermal shock at 200°C for 4 h | No flowing or crack | No flowing or crack |
| Tensile strength after diesel exposure at 23°C for 24 h | ≥10.4 MPa | ≥15 MPa |
| Elongation after diesel exposure at 23°C for 24 h | ≥200% | ≥400% |
| Tensile strength after diesel exposure at 50°C for 24 h | ≥12 MPa | — |
| Elongation after diesel exposure at 50°C for 24 h | ≥400% | — |
DR Diesel Resistant Heat-shrinkable Tubing is offered in nominal sizes from 1/8 in. through 2 in. The listed minimum inside diameters before shrinking range from 3.2 mm to 50.8 mm, while the stated maximum inside diameters after shrinking range from 1.6 mm to 25.4 mm for the corresponding sizes.
| Nominal size | Before shrink | After shrink | Supply length |
|---|---|---|---|
| 1/8 in. | 3.2 mm | 1.6 mm | 50 m |
| 1/4 in. | 6.4 mm | 3.2 mm | 50 m |
| 1/2 in. | 12.7 mm | 6.35 mm | 30 m |
| 1 in. | 25.4 mm | 12.7 mm | 30 m |
| 2 in. | 50.8 mm | 25.4 mm | 1 m |
Measure the largest section that must pass through the tube before heating, then confirm that the recovered diameter can fit the intended covered area. Larger external diameter does not automatically provide better protection. The correct choice depends on bundle geometry, coverage, and installation space. Confirm service conditions before finalizing a size.
DR Diesel Resistant Heat-shrinkable Tubing is intended for cable and wire-harness protection in demanding transportation and equipment settings. In automotive harnesses, it can be evaluated for routes where diesel, lubricants, temperature cycling, or chemical contact are relevant. In aviation and aerospace assemblies, its stated resistance profile and conformance information provide a basis for further engineering review. For military harnesses, compare program requirements with qualification requirements.
For an electric cable protective sleeve application, this product provides heat-shrinkable coverage rather than a loose mechanical cover. It may be considered with an assorted heat shrink tubing range when several harness diameters must be reviewed, but each selected sleeve must still match its required service condition. Wire marker tape and red heat shrink can support identification practices; they should not be substituted for diesel-resistant material validation.
Prepare the harness so the selected DR Diesel Resistant Heat-shrinkable Tubing size can pass over the largest component before heating. Position the sleeve over the protection area, apply heat evenly, and inspect the recovered tubing for uniform contact. Unsuitable sizing or uneven heating can produce an unsatisfactory fit even when the tubing is otherwise correctly specified. Use a heating method suited to assembly instructions and safety requirements.
Evaluate temperature and fluid exposure together. A route may be hot, but fluid contact could be the condition that drives the material decision. Conversely, diesel resistance is not universal approval for every chemical or system. Confirm expected medium, exposure duration, service temperature, and any required standard or test method before production release.
DR Diesel Resistant Heat-shrinkable Tubing combines flexible special-elastomer construction, 2:1 shrinkage, a broad stated operating range, and documented diesel-exposure performance indicators. A sound selection process reviews temperature, shrinking conditions, size, fluid exposure, and program requirements rather than relying only on a generic product category. For special dimensions or documentation requests, provide harness dimensions, temperature range, exposure medium, and target application. Other pipe specifications can be provided according to customer requirements.
DR diesel resistant heat-shrinkable tubing is made of special elastomer with a 2:1 shrinkage rate. Resistant to high temperature, flame retardant, oil and chemicals, flexible and especially resistant to diesel. Widely used for aviation, aerospace and military cables and wire harnesses, and automotive wire harnesses, with good resistance to diesel, aviation fuel, hydraulic fluid, lubricating oil and more.
Download Product Manual: