CR-BS-6001 is designed with buckle structure, which can be installed without the use of any tools. This product can effectively reduce the wear and tear problem of wire harnesses and cables in use and provide a reliable guarantee for line safety.
Download Product Manual:
Button PVC Wrap-CR-BS-6001 is a PVC wire-harness wrap with a buckle closure for organizing and protecting grouped cables. It is designed for cable runs that may need to be opened again during inspection, modification, or maintenance. Rather than requiring a permanent wrap or a heat-applied process, the closure can be opened and reclosed along the bundle. This makes Button PVC Wrap-CR-BS-6001 a practical option where orderly routing and later access both matter.
The product combines electrical insulation and abrasion protection with a documented working-temperature range of –15°C to +105°C. Its flammability result is UL 94 VTM-0. These specifications help buyers compare the material with the environmental and safety requirements of their own installation; they should not replace project-specific qualification or compliance review.
The defining feature of Button PVC Wrap-CR-BS-6001 is its buckle structure. It can be installed without tools, then reopened where access is needed. For an assembly team, this can simplify a cable-routing task when conductors need to be added, checked, or replaced after the first installation. The wrap is intended to close around a cable bundle rather than require the bundle to be threaded through a fixed sleeve.
The product uses PVC material to provide electrical insulation and a protective layer between cables and surrounding enclosure surfaces. In cabinets and equipment, cables can contact chassis edges, mounting hardware, or nearby components. A properly selected wrap helps keep the bundle organized while reducing direct surface contact. Final protection performance depends on the installation, cable type, movement, and local operating conditions.
The stated operating range is –15°C to +105°C. The product is also specified as UL 94 VTM-0 for flammability. These are useful facts for a technical review, especially where wiring is installed inside electrical equipment. Buyers should request applicable test documentation and confirm the relevant standard, target market, and finished-equipment requirements before approving a design.
The PVC construction is soft and pliable for routing around typical bends in computer housings, panel boards, and industrial electrical equipment. The product is offered in 14 nominal inner-diameter sizes, allowing a buyer to align a selected size with the cable-bundle diameter instead of using one oversized wrap for every harness.
For a cable route that is serviced periodically, this buckle wrap can be opened for access and closed again after the work is complete. This is different from a single-use covering that must be cut away and replaced. The useful result is straightforward: technicians can retain the organized bundle while reaching a specific part of the run. Evaluate closure fit on the actual bundle, particularly when the bundle approaches the selected nominal diameter.
| Parameter | Stated value |
|---|---|
| Material | PVC |
| Flammability | UL 94 VTM-0 |
| Working temperature | –15°C to +105°C |
| Nominal inner diameter range | 12 mm to 150 mm |
| Reel length | 75 m per box |
Button PVC Wrap-CR-BS-6001 is supplied across a range from 12 mm to 150 mm nominal inner diameter. All listed sizes are supplied on 75 m reels per box. The developed width changes by size, so dimensional selection should use the correct part number and the relevant specification rather than the nominal diameter alone. Custom colors, fixed-length cutting, and non-standard sizes are described as available on request.
| Nominal I.D. (mm) | Developed width (mm) |
|---|---|
| 12 | 60 ± 5 |
| 15 | 67 ± 5 |
| 19 | 80 ± 5 |
| 25 | 100 ± 8 |
| 31 | 120 ± 8 |
| 37 | 140 ± 8 |
| 40 | 148 ± 10 |
| 44 | 160 ± 10 |
| 51 | 180 ± 15 |
| 57 | 202 ± 15 |
| 60 | 210 ± 15 |
| 70 | 242 ± 15 |
| 100 | 335 ± 15 |
| 150 | 495 ± 15 |
Within computers and office equipment, Button PVC Wrap-CR-BS-6001 can group internal wires and help separate them from chassis edges and brackets. Its re-openable construction is relevant when equipment is upgraded or serviced. Confirm bundle size, local temperature exposure, and any equipment-specific safety requirement before selection.
For distribution boards and control cabinets, Button PVC Wrap-CR-BS-6001 can organize conductors for a cleaner routing path while allowing later inspection or modification. The stated flammability classification and temperature range provide reference points for engineering review. They do not by themselves certify an assembled cabinet or replace the applicable panel standard.
In industrial electrical devices, this PVC wrap can be used where a flexible protective wrap is needed around a wire harness. The range of nominal sizes supports varied bundle diameters. For moving, high-vibration, unusually hot, or otherwise demanding locations, assess the complete installation and validate the selected size under actual service conditions.
Before purchase, review the cable bundle after connectors, branches, labels, and protective layers are in place. Measure the finished outside diameter, note the available routing space, and test a representative sample. That practical check helps confirm closure operation, service access, and compatibility with the intended equipment layout. Document the result for repeat orders and installation instructions.
Keep the supplier drawing, approved sample, and installation record with the project file so later maintenance teams can identify the chosen size and routing method without guesswork.
Select Button PVC Wrap-CR-BS-6001 by measuring the finished cable bundle and comparing it with the relevant nominal inner diameter. If the bundle is close to the upper limit of a selected size, assessing the next size up can help confirm comfortable buckle closure. A sample installation is a sensible way to verify routing, closure feel, and maintenance access before a larger order.
Button PVC Wrap-CR-BS-6001 is part of a wider wire-protection product range that includes corrugated conduit, glass fiber sleeving, heat-shrink tubing, and wire-harness tape. When documentation is required, ask for the appropriate material data, dimensional specification, or flammability test report. This product information is intended to support selection discussions; the buyer remains responsible for confirming suitability in the final application.
CR-BS-6001 is designed with buckle structure, which can be installed without the use of any tools. This product can effectively reduce the wear and tear problem of wire harnesses and cables in use and provide a reliable guarantee for line safety.
Download Product Manual: