CR-BS-4009 is made of polyester monofilament and multifilament. It has good wear resistance, heat dissipation performance and is easy to install and remove.
Download Product Manual:
Braided Self-closing Wrap-CR-BS-4009 is a polyester protective sleeve for cable and hose bundles. It is made from monofilament and multifilament yarns and uses an open braided construction with a self-closing overlap. The design allows a technician to place protection around an assembled bundle instead of feeding every wire through a closed tube. This is useful when connectors, branches, or irregular routing make conventional sleeving difficult to install. The sleeve can be opened for inspection, cable additions, or rerouting, then closed again around the protected run.
The open structure is intended to support heat dissipation around the bundle while providing a mechanical protective layer. It is not presented as a permanently sealed termination product. If a route requires water-tight sealing, a separate sealing method should be selected for the interface or termination.
The supplied product information identifies polyester monofilament and multifilament as the construction materials. Its stated working temperature range is -40°C to +150°C. The supplied test table reports low-temperature resistance at -40°C for four hours and heat-aging resistance at 175°C for 240 hours, with no cracking or degradation reported. These figures provide an engineering reference, but the finished assembly should always be evaluated against its actual thermal load, routing arrangement, and customer validation requirements.
The supplied abrasion result is more than 10,000 cycles under ISO 6722-1. The listed flammability reference is FMVSS 302 with a burn rate below 100 mm/min. Resistance to gasoline and engine fluids is also stated in the product material. Where a project needs a specific approval, test report, or regional compliance package, request the applicable documentation during qualification.
The supplied specification calls for at least 25% edge overlap. Preserve that overlap after installation, especially at bends, breakouts, and transitions where a bundle may change shape or diameter.
For an assembled harness, the self-closing format can reduce the need to disconnect connectors simply to add a protective cover. Position the sleeve along the required route, close the overlap around the bundle, and check that the closure remains secure through bends and at mounting points. Braided Self-closing Wrap-CR-BS-4009 is designed for accessible protection, so future inspection or changes can be made without destroying the sleeve during removal.
Selection should begin with the real bundle, not a single loose cable. Include branches, clamps, connectors, bend radius, and any required clearance when choosing a nominal size. A cover that is too small may not retain the required overlap; one that is too large may not provide the intended fit. Confirm the final assembly with a representative sample where service access or vibration is critical.
The supplied range includes nominal inner diameters of 5, 8, 10, 13, 16, 19, 25, 32, 38, and 50 mm. Applicable ranges are listed as 4–6, 7–9, 10–11, 12–14, 15–17, 18–22, 23–28, 29–35, 36–45, and 46–54 mm respectively. Reel lengths vary by size from 25 m to 200 m. Products can be cut to fixed length as required, and other sizes are available upon request.
| Nominal I.D. | Applicable range | Reel length |
|---|---|---|
| 5 mm | 4–6 mm | 200 m |
| 8–16 mm | 7–17 mm, by size | 100 m |
| 19–25 mm | 18–28 mm, by size | 50 m |
| 32–50 mm | 29–54 mm, by size | 25 m |
Automotive routes may combine vibration, abrasion, heat, and the need for later inspection. Braided Self-closing Wrap-CR-BS-4009 can be evaluated for these routes where a re-enterable, open-braid cover is appropriate. The listed temperature range, abrasion reference, flame-retardancy result, and resistance to gasoline and engine fluids are relevant facts for a technical review. They do not remove the need to check the vehicle program’s specific material, flammability, mounting, and fluid-exposure requirements.
At contact points, identify the source of movement and confirm that the cover, clips, and surrounding structure work together. A sleeve is one part of the routing system; clamp placement and bend control also influence long-term protection.
In control cabinets, server enclosures, and telecommunications equipment, a bundle may need organization while remaining accessible for future changes. The open construction allows airflow around routed cables, and the closure can be reopened when conductors are added or moved. This makes the product a practical option for serviceable cable-management sections. Evaluate the whole assembly, including electrical, fire, and installation requirements, before specifying a final configuration.
Railway carriage routes and industrial equipment can expose cable or hose bundles to repeated movement and contact with adjacent structures. The product can be considered where a serviceable protective sleeve and abrasion reference are needed. Its stated size range also supports selection across a variety of standard bundle dimensions. For industrial hose applications, confirm the chemical, temperature, pressure, and mechanical conditions of the installation before use.
Begin with the required protective function: abrasion management, accessible maintenance, airflow around the bundle, or a flammability review. Braided Self-closing Wrap-CR-BS-4009 is most relevant where the bundle must remain accessible after installation. If permanent shrink sealing is required at a termination, use an appropriate dedicated solution there and evaluate this sleeve for the accessible run between terminations.
The supplied material notes manufacturing certifications including ISO 9001, IATF 16949, ISO 14001, ISO 45001, and GJB9001C. For supplier approval, request current supporting documents and confirm that they apply to the intended program. Provide bundle diameter, target length, routing environment, expected temperature, contact points, and required documentation when requesting a size recommendation.
CR-BS-4009 is made of polyester monofilament and multifilament. It has good wear resistance, heat dissipation performance and is easy to install and remove.
Download Product Manual: