CR-BS-8002 is a square protective sleeve specifically designed for aluminum busbars used in electric vehicle charging. It is woven by blending polyester multifilaments and monofilaments. It’s orange color facilitates the identification of high-voltage wire harnesses, and it features properties such as wear resistance, corrosion resistance, and easy installation. The product can be customized according to customer requirements and can be enhanced with electromagnetic shielding performance.
Download Product Manual:
Aluminium Busbar Wrap-CR-BS-8002 is a square protective sleeve designed for rectangular aluminium busbars used in electric-vehicle charging equipment and related high-voltage assemblies. It is woven from polyester multifilaments and monofilaments, creating a sleeve format intended to sit around a flat-sided busbar profile rather than a round cable. The orange construction helps identify high-voltage wire-harness areas during assembly and service. Aluminium Busbar Wrap-CR-BS-8002 is intended for buyers who need a documented starting point for busbar abrasion protection while retaining the option to confirm dimensions and project-specific requirements with the supplier.
The supplied product material describes Aluminium Busbar Wrap-CR-BS-8002 as wear-resistant, corrosion-resistant, and easy to install. It also states that the sleeve can be customized to customer requirements and can be enhanced with electromagnetic shielding performance. Where shielding, insulation coordination, or a specific approval package is required, request the applicable technical documentation and sample evaluation rather than treating the general product description as a project certification.
Aluminium Busbar Wrap-CR-BS-8002 is therefore best evaluated as part of the complete electrical and mechanical assembly. Confirm whether the sleeve needs to protect against vibration contact, assembly handling, enclosure interfaces, or a combination of these conditions. This condition-led approach helps prevent over-specifying a feature that is not needed or overlooking a test requirement that is essential.
The existing product content reports typical test information for Aluminium Busbar Wrap-CR-BS-8002. These values should be read as product information, not as a substitute for a project acceptance plan. The reported thermal-aging impact test is 175°C for 336 hours, with no cracking or degradation stated after the test. The reported abrasion result is ISO 6722-1 Class 6 and more than 30,000 abrasion cycles. The stated flammability result is FMVSS 302, described as self-extinguishing after flame removal. The listed operating temperature range is −40°C to 150°C.
| Item | Reported information |
| Thermal aging impact test | 175°C for 336 hours; no cracking or degradation stated |
| Abrasion resistance | ISO 6722-1 Class 6; more than 30,000 abrasion cycles stated |
| Flammability | FMVSS 302; self-extinguishing after flame removal stated |
| Operating temperature | −40°C to 150°C stated |
The supplied specification table for Aluminium Busbar Wrap-CR-BS-8002 lists six part numbers: CR-BS-80020825, CR-BS-80020925, CR-BS-80021025, CR-BS-80021225, CR-BS-80021325, and CR-BS-80021425. Listed widths are 32 ± 2 mm, 38 ± 2 mm, or 40 ± 2 mm. Listed heights range from 7 to 18 mm, thickness is 0.8 ± 0.2 mm, overlap is greater than 8 mm, and cut length is customizable. These numbers are useful for an initial envelope check, but the final selection should also account for terminals, insulation transitions, brackets, and service access.
When comparing heat shrink tubing sizes mm, do not assume that a heat-shrink product and a woven square sleeve solve the same installation problem. A shrinkable tube typically relies on heat activation and a particular recovered diameter; Aluminium Busbar Wrap-CR-BS-8002 is described as a woven square protective sleeve. For an application currently using 1 heat shrink tubing, compare the required installation process, profile fit, temperature exposure, and protection objective before choosing a replacement or complementary component.
Aluminium Busbar Wrap-CR-BS-8002 is positioned for aluminium busbars in EV charging systems. In charging equipment, the orange visual identity can support quick recognition of a high-voltage area, while the square sleeve concept addresses a rectangular conductor profile. Verify the final routing, enclosure temperature, and safety requirements for the charging design.
For battery-pack or stationary energy-storage busbars, Aluminium Busbar Wrap-CR-BS-8002 can be considered where the supplied temperature range, abrasion information, and customizable cut length align with the design brief. The product material supports an initial discussion of busbar protection; it does not establish suitability for every battery architecture without an engineering review.
High-voltage distribution boxes and power-distribution units may include closely routed conductors and enclosure interfaces. Aluminium Busbar Wrap-CR-BS-8002 can be evaluated for physical protection around rectangular busbar sections where vibration or contact wear is a concern. Confirm spacing, dielectric requirements, and any system-level test obligations separately.
Before release, compare the supplied sleeve sample with the assembled busbar, including corners, joints, supports, and the route through the enclosure. This controlled comparison supports a more reliable selection than relying on catalogue dimensions alone.
Aluminium Busbar Wrap-CR-BS-8002 differentiates itself through the combination of a square profile, polyester woven construction, orange high-voltage identification, reported abrasion performance, and customizable format. The central advantage is not simply adding a sleeve; it is matching a protection format to the shape of an aluminium busbar. That match can make layout and protection discussions more focused for engineers and purchasing teams.
For procurement, ask for the busbar dimensions, expected service conditions, target quantity, required cut length, and any documents needed for supplier qualification. Aluminium Busbar Wrap-CR-BS-8002 can then be reviewed against a clear application brief. If the project requires shielding, a special size, or a verification report, state that requirement at the inquiry stage so the proposed configuration and evidence can be aligned with the intended use.
CR-BS-8002 is a square protective sleeve specifically designed for aluminum busbars used in electric vehicle charging. It is woven by blending polyester multifilaments and monofilaments. It’s orange color facilitates the identification of high-voltage wire harnesses, and it features properties such as wear resistance, corrosion resistance, and easy installation. The product can be customized according to customer requirements and can be enhanced with electromagnetic shielding performance.
Download Product Manual: